
This is a complete kit to build a fully functioning watermaker. More information can be found under info sections. Choose from the different variants below.
"Flush" MAB Watermaker with control panel
Comet Pump high pressure pump
Anodized, cast aluminum crankcase
Solid ceramic pistons
Stainless steel check valves and piston guides
3/8″ FPT inlet – 3/8″ FPT outlet except where noted
High quality double-sealing V-packings
Reversible crankshaft for easy right or left hand mounting
Forged bronze connecting rods with lifetime warranty
Die-cast, anodized aluminum crankshaft - fine design for optimal operating temperature
Hardened stainless steel piston guides
High-efficiency stainless steel check valves
High quality large ball bearings
Anti-slip, heat-resistant, industrial ceramic pistons
High speed optical oil bath
5 year manufacturer's warranty
To ensure safe and reliable operation of a powerful 12 VDC motor, the following should be considered:
✅ Use battery cables with the correct dimension to handle high current. ✅ Ensure that all contact points are properly connected and in good condition. ✅ Check and maintain the connections regularly to avoid overheating and short circuits.
Failure to do so may result in overheating and damage, which can lead to short circuits and serious risks to both the engine and electrical system.
The control panel controls and monitors the watermaker with functions for start/stop, pressure adjustment, and automatic and manual cleaning. It includes a TDS meter for water quality, safety valves for pressure protection and automatic shut-off in case of pressure drop in the seawater pump. For longer downtimes, typically over 3–7 days, a programmable self-cleaning function can be activated to extend the life of the membranes and minimize the risk of fouling.
Parts included in the complete MAB Watermaker kit
Control panel
AMAB Hydraulic couplings and connections for high pressure in acid-resistant stainless steel
Needle valve acid-proof stainless steel for adjusting high pressure
1 high-pressure hose 4 m between pressure housing/RO Membrane and control panel (please advise if a different length is required)
1 high-pressure hose 4 m between high-pressure pump and RO membrane (please advise if a different length is required)
Double filter housing
Single filter housing for carbon filter
Pre-filter 5 and 20 micron
carbon filter
Boost pump
Flushing pump
Technical description and manual.
High pressure pressure gauge 0-100 bar
Pressure gauge for the low pressure part 0-4 bar
Water flow meter for ongoing drinking water production l/min
Water quality meter, TDS meter shows value in real time
Automatic fresh water flushing with precise time and week settings
Pre-filter micron 20
pre-filter micron 5
Carbon filter (fresh water flushing)
RO memberan seawater 2540
High pressure housing for reverse osmosis
1 three-way valve for redirecting drinking water to water tank or direct tapping
1 three-way valve for redirecting flushing or preservation
Complete set of quick couplings for 12 mm hose (see quick couplings)
15 m water hose (12 mm) for connecting the low-pressure components of the system units
Low voltage flat cable (P27, marine)
hose cutter for cutting fine sections of the water hose (P45)
Glycerol for lubricating o-rings (P46)
Pickling (P47)
DMfit quick couplings offer a tool-free, leak-proof and food-grade solution for easy connection and removal. Thanks to their push-fit mechanism, installation is both easy and safe.
Contents of the kit (incl. 15 meters of low-pressure hose): (see pictures)
Check valves (P01, 2 pcs)
Three-way valves (P11, 2 pcs)
Two-way distributor (P13, 1 pc)
Tee-union OD Tube 12 mm (P05, 1 pc; P06, 1 pc)
Threaded-to-hose adapter 1/2" x 12 mm (P10, 4 pcs)
Pipe elbows female - female 12 mm (P15, 4 pcs)
Pipe elbows female - male 12 mm (P12, 4 pcs)
Bypass boost pump/system (P23, 1 pc)
This is not included (due to every installation being different)
Battery cables from the boat to the system
Seawater penetration
Connection to the boat's existing water tank
